Przedmiotem wynalazku jest narzedzie do odcinania skib, umocowane z przodu ciagnika.Zwiekszenie sily uciagu ciagnika podczas orki, a tym samym i lepsze wykorzystanie mocy jego silnika, odbywa sie najczesciej przez dociazenie tylnej osi ciagnika za pomoca podnosnika hydrauli¬ cznego. Wada takiego rozwiazania jest przeciazenie tylnej osi, przy jednoczesnym odciazeniu osi przedniej co pogarsza kierowalnosc ciagnika i nie pozwala, wciagnikach z napedem na obie osie, w pelni wykorzystac napedzanej osi przedniej do wzmocnienia sily uciagu. Znane sa wprawdzie rozwiazania, w których czesc korpusów pluga zamocowana jest na przodzie ciagnika, przez co nastepuje dociazenie przedniej osi, ale sa to rozwiazania drogie, poniewaz wymagaja dodatkowego, pchanego pluga.Celem wynalazku jest opracowanie prostego urzadzenia, które zamocowane na przodzie ciagnika, przejmowaloby czesc funkcji pluga i jednoczesnie, przez swoje dzialanie, powodowaloby dociazenie przedniej osi ciagnika.Cel ten osiagniety przez wykonanie narzedzia skladajacego sie z belki poprzecznej z zamoco¬ wanymi do niej krojami, których liczba jest równa liczbie korpusów pluga. Plaszczyzny dzialania krojów musza pokrywac sie z plaszczyznami odcinania skib przez korpusy pluga.Przedmiot wynalazku jest przedstawiony w przykladzie wykonania na rysunku, razem z plugiem i ciagnikiem, w widoku z góry.Narzedzie wedlug wynalazku sklada sie z belki poprzecznej 1 i przymocowanych do niej krojów 2 w odstepach równych szerokosci skiby odcinanej przez korpusy pluga 3. Liczba krojów 2 jest równa liczbie korpusów pluga 3, a plaszczyzny dzialania krojów 2 pokrywaja sie z plaszczy¬ znami odcinania skib przez korpusy pluga. Belka poprzeczna 1 wraz z krojami 2 zamocowana jest na przodzie ciagnika 4 za pomoca trzypunktowego mechanizmu zawieszenia i przedniego podnos¬ nika hydraulicznego.Pionowe, skierowane ku dolowi, skladowe oporu skrawania krojów 2 dociazaja przednia os ciagnika 4 i poprawiaja w ten sposób wspólczynnik wykorzystania mocy silnika ciagnika 4.Narzedzie wedlug wynalazku moze byc stosowane do istniejacych plugów. Jest ono latwe do wykonania, a jedynym warunkiem jego uzytkowania jest wyposazenie ciagnika w dodatkowy przedni podnosnik hydrauliczny.2 128937 Zastrzezenie patentowe Narzedzie do odcinania skib, mocowane z przodu ciagnika za pomoca trzypunktowego mechanizmu zawieszania i przedniego podnosnika hydraulicznego, znamienne tym, ze sklada sie z belki poprzecznej (1) z zamontowanymi do niej krojami (2), których liczba jest równa liczbie korpusów pluga a plaszczyzny dzialania krojów (2) pokrywaja sie z plaszczyznami odcinania skib przez korpusy pluga.Pracownia Poligraficzna UP PRL. Naklad 100 egz.Cena lt)0 zl PLThe subject of the invention is a tool for cutting furrows attached to the front of the tractor. Increasing the tractive force of the tractor during plowing, and thus better use of its engine power, is usually done by weighting the rear axle of the tractor with a hydraulic jack. The disadvantage of such a solution is the overloading of the rear axle, while at the same time relieving the front axle, which reduces the maneuverability of the tractor and does not allow, both-axle-driven hoists, to fully use the driven front axle to increase the pulling power. Although there are known solutions in which a part of the plow bodies is mounted at the front of the tractor, which causes the front axle to be loaded, they are expensive solutions, because they require an additional, pushed plow. The aim of the invention is to develop a simple device that, when attached to the front of the tractor, would take over part of the function of the plow and, at the same time, by its action, it would cause a load on the front axle of the tractor. This goal was achieved by making a tool consisting of a crossbeam with cuts attached to it, the number of which is equal to the number of plow bodies. The operating surfaces of the cutters must coincide with the cut-off surfaces of the furrows by the plow bodies. The subject of the invention is shown in the example of the drawing, together with the plow and the tractor, in top view. The tool according to the invention consists of a cross beam 1 and cut cutters 2 attached to it at intervals equal to the width of the furrow cut by the plow bodies 3. The number of cuts 2 is equal to the number of plow bodies 3, and the operating planes of the cuts 2 coincide with the planes of cutting the furrows by the plow bodies. The crossbeam 1 with the cutters 2 is attached to the front of the tractor 4 by means of a three-point linkage and a front hydraulic lift. The vertical, downward cutting resistance components of the cuts 2 load the tractor front axle 4 and thus improve the engine power utilization ratio 4. The tool according to the invention can be applied to existing plows. It is easy to implement, and the only condition for its use is that the tractor is equipped with an additional front hydraulic lift.2 128937 Patent claim Tool for cutting furrows, attached at the front of the tractor by means of a three-point linkage and a front hydraulic lift, characterized by the fact that it consists of of the crossbeam (1) with the cutters (2) mounted to it, the number of which is equal to the number of plug bodies and the cut surfaces (2) work in line with the cut-off surfaces of the furrow bodies by the plug bodies. Mintage 100 copies Price lt) PLN 0 PL