Przedmiotem zgłoszenia jest łóżko do kampera, inaczej nazywanego samochodem kempingowym. Łóżko ma ramę, która składa się z pierwszej krawędzi (1) oraz z drugiej krawędzi (2), połączonych ze sobą podłużnicami (3). Rama jest zawieszona na dwóch giętkich cięgnach (4), w tym przykładzie wykonania są to linki, których górne końce są zamocowane w belce (8) przykręconej do ściany kampera. Rama jest zawieszona na cięgnach (4) pierwszą krawędzią (1), na której zamocowane są pierwsze ślizgi (5). Cięgna (4) opasują pierwsze ślizgi (5) od strony ściany i od dołu tak, że ten koniec ramy wisi w zagięciu cięgien (4), gdyż po opasaniu pierwszych ślizgów (5) cięgna (4) ciągną się poniżej podłużnic (3) ramy do drugich ślizgów, zamocowanych do drugiej krawędzi (2) ramy i opasują te drugie ślizgi od góry i z boku. Po opasaniu drugich ślizgów cięgna są poprowadzone pionowo w stronę podłogi i tam drugie końce cięgnie (4) są zamocowane w podłodze. Druga krawędź (2) ramy jest podparta siłownikami liniowymi, których górne końce są zamocowane do drugiej krawędzi (2) ramy a dolne końce siłowników liniowych są osadzone trwale w podłodze. Cięgna (4) mają stałą długość, obydwa są jednakowe. Rozsuwając siłowniki o odcinek „x” o tyle samo skraca się odległość „b”, rama łóżka zatem cały czas jest pozioma a jej ruch jest determinowany przez cięgna (4), po których rama ślizga się ślizgami (5). Dla zapobieżenia niekontrolowanym wahaniom łóżka w pierwszej krawędzi (1) zamocowany jest poprzeczny zatrzask (10) do współpracy z pionową listwą zatrzaskową (9), mocowaną do ściany. Po ustaleniu wysokości ramy nad podłogą zatrzask (10) blokuje ramę w listwie (9).The subject of the application is a bed for a motorhome, otherwise known as a motorhome. The bed has a frame that consists of a first edge (1) and a second edge (2) connected to each other by stringers (3). The frame is suspended on two flexible rods (4), in this embodiment these are cables whose upper ends are fixed in a beam (8) screwed to the wall of the motorhome. The frame is suspended on the tie rods (4) with the first edge (1) on which the first slides (5) are mounted. The rods (4) surround the first slides (5) from the wall side and from the bottom so that this end of the frame hangs in the bend of the rods (4), because after the first slides (5) are wrapped, the rods (4) extend below the frame side members (3) to the second shoes attached to the second edge (2) of the frame and surround the second shoes from the top and side. After the second shoes are wrapped around, the tie rods are led vertically towards the floor and there the other ends of the tie rods (4) are secured in the floor. The second edge (2) of the frame is supported by linear actuators whose upper ends are attached to the second edge (2) of the frame and the lower ends of the linear actuators are firmly embedded in the floor. The tie rods (4) are of a constant length, both are the same. Moving the actuators apart by the segment "x", the distance "b" is shortened by the same amount, therefore the bed frame is always horizontal and its movement is determined by the links (4) on which the frame slides (5). To prevent uncontrolled swing of the bed, a transverse latch (10) is fitted to the first edge (1) to cooperate with a vertical latch bar (9) fixed to the wall. After fixing the height of the frame above the floor, the latch (10) locks the frame in the rail (9).